|
12-16-2015, 01:36 AM,
|
|
|
dgk196
Technical Sergeant
|
Posts: 142
Joined: May 2008
|
|
PzC manual....
Hello....
Does anyone have a link for a PzC manual that has the 'HotKeys' list included in it.... thanks much for your help with this.
Dennis 
|
|
|
|
12-16-2015, 03:53 AM,
|
|
|
dgk196
Technical Sergeant
|
Posts: 142
Joined: May 2008
|
|
RE: PzC manual....
(12-16-2015, 03:08 AM)Mr Grumpy Wrote: This list is from the F14 manual but I hope it should be the same as for a PzC title?
Hot Keys
The following Hot Keys are supported in the main program. Note that these
Hot Keys are defined as command accelerators of the main program main
window and therefore the main window must have the keyboard focus for
these to work (that is, the main window must have a highlighted title bar).
Ctrl Key – toggle between Move Mode and Fire Mode.
Shift Key - display the on-map labels while this key is pressed.
Space Bar - display the Selection Dialog (useful in Full Screen mode).
F1 - invoke General Help (display this help file).
F2 – display Users Manual help file.
F3 – display Campaign Notes help file.
F4 – display Parameter Data values.
F5 – slow the speed of the A/I processing.
F6 – return A/I processing to normal speed.
F7 – increase the speed of the A/I processing.
F8 – put the A/I in the highest possible processing mode (use F6 to return to
normal).
A - invokes the Air Mission Dialog.
B - move the selected units backward in the Hot Spot hex (Note: this only has
a visible effect in the 3D graphics mode).
D - selected unit(s) will begin Digging In.
E - invokes the Artillery Dialog.
F - move the selected units forward in the Hot Spot hex (Note: this only has a
visible effect in the 3D graphics mode).
G – toggle display of valid target hexes of selected units.
H – toggle display of maximum range of selected units.
I - activates the AI.
J - opens the Jump Map.
K - displays the modified Command Range from a selected HQ.
M – opens the Arrived Dialog.
N - advance the Hot Spot to the next stack of units that have not been active
this phase. If you hold down the Alt key when invoking this function, it will
advance the Hot Spot to the next unit that has not been active and select it. If
you hold down the Ctrl key, it will advance the Hot Spot to the next unit that is
capable of firing.
O - highlights the Organization for the selected unit. If an organization is
currently selected and you hold down the Alt key when invoking this function,
then the next higher organization is selected.
P – display the Organization Dialog.
Q – highlights HQ units on the map.
R – toggle Rail Mode for the selected units.
S - displays Visible hexes from the Hot Spot
T - toggles Travel Mode for selected unit(s)
U - undo the last movement (not available under Fog-of-War).
V - display Divisional Markings.
W – highlights Indirect Fire Spotters.
X - remove the selected units from the map.
Y – toggle display of Reachable Hexes.
Z - toggles the full screen map display on and off.
1 - display the map in Zoom-Out 2D mode.
2 - display the map in Normal 2D mode.
3 - display the map in Zoom-Out 3D mode.
4 - display the map in Normal 3D mode.
5 - display the map in Magnified 2D mode.
Normally the screen is recentered on the Hot Spot hex when you change zoom
modes. If you hold down the Alt key when you change zoom modes, the
screen will retain the current view.
You can also use the mouse wheel to zoom in and out. The program will
attempt to position the map to keep the hex you have the cursor over when this
is done.
Keypad 0 - change the formation of the selected units.
Keypad 1 - move the selected units down and to the left one hex.
Keypad 2 - move the selected units down one hex.
Keypad 3 - move the selected units down and to the right one hex.
Keypad 4 - turn the selected units counterclockwise.
Keypad 5 - turn the selected units about-face.
Keypad 6 - turn the selected units clockwise.
Keypad 7 - move the selected units up and to the left one hex.
Keypad 8 - move the selected units up one hex.
Keypad 9 - move the selected units up and to the right one hex.
Delete - move the selected units counterclockwise.
Page Down - move the selected units clockwise.
Home - move the selected units forward in the Hot Spot hex (Note: this only
has a visible effect in the 3D graphics mode).
End - move the selected units backward in the Hot Spot hex (Note: this only
has a visible effect in the 3D graphics mode).
Hello.... thanks much for the reply... lost my ability to access 'help' files... an ongoing problem with Windows 10...
Dennis 
|
|
|
|
12-16-2015, 08:45 AM,
|
|
|
tbridges
Warrant Officer
|
Posts: 273
Joined: Mar 2007
|
|
|
RE: PzC manual....
I have the same problem. I have Adobe Acrobat and still cannot pull up help files when "in game".
Acrobat works fine for all other applications.
|
|
|
|
12-16-2015, 09:47 AM,
|
|
|
tbridges
Warrant Officer
|
Posts: 273
Joined: Mar 2007
|
|
RE: PzC manual....
(12-16-2015, 09:34 AM)Mr Grumpy Wrote: How strange, is that in both the PzC and FWWC series titles?
Both F14 and EP14 work fine for me, but I don't have any PzC titles loaded yet.
I only have the PzC and MC games.
|
|
|
|
12-18-2015, 08:13 AM,
|
|
|
tbridges
Warrant Officer
|
Posts: 273
Joined: Mar 2007
|
|
RE: PzC manual....
(12-18-2015, 06:19 AM)Mr Grumpy Wrote: OK so maybe it is a PzC/MC series issue??
Acrobat worked fine in the games with Windows 8.1. Now I have Windows 10 so it must be somehow related to Windows 10. I wonder if others are also having this issue?
|
|
|
|
12-20-2015, 02:03 AM,
|
|
|
Sgt Jasper
Lieutenant Colonel
|
Posts: 658
Joined: Jan 2001
|
|
|
RE: PzC manual....
I have PzC, FWWC, and PzB games all running in Win 10, no problems with help/manual files. Can you open them directly with Acrobat rather than going through the in-game routine?
|
|
|
|
Archived Forums
Help
Calendar
Member List
Search
){kind=link}
